It may be a little while, as other things have got in the way.Īnyway, came downstairs in the morning, ready for a cup of coffee and a bit of breakfast before going to work, and I step in a pool of water. If you follow my YouTube channel, you'll be waiting for an update on the Sony 9-306. Ring so it doesn't bind the latch handle (meaning it's free to move).It's been busy lately. Let go of latch (it snaps into "closed" position) and adjust Slip the ring over the latch handle and get it into approximate Replace front "ring": Open door and, while pulling out on latch handle, Test latch with door open - is it working? Try Slip new latch assy into place, pressing vertical "hinge pin" and ends Note the way the ends of the spring go under the 2 screws. Using a 1.5mm Torx screwdriver, remove 2 small screws holding broken Once it starts coming apart, just work the Unsnap (separate) them by either getting your fingernails into the seamĪnd pulling them apart - or prying them open with a spackle knife or Pieces (front and rear) snapped together - with a seam around periphery. Open door, and notice white plastic "ring" around glass is actually 2 Once you've received your new latch assy (about $20): Him which model machine you need a door latch for (if you aren't sure, Of course you can do it yourself.įirst call Joel (Malber in NY) at 80 or 51. I like to snap a digital picture before I start so I can reference back if I forget what goes where. Do one side at a time, if one side is broken do that side first so you have a a guide to look at if you forget where something goes. Once out you will see the cable (24) that attaches to the spring (18) and to the hinge on the door (not shown), replace the cable and pulley (9). Look at the plumbing and electrical to make sure there is enough length to move it out. Disconnect the power or unplug the power cord before working on this! To replace you will need to pull the dishwasher out from the cabinet opening about a foot. It comes with 2 ropes (24), 2 pulleys (9 &17). The part number for this kit is 8194001.(See image below) It comes complete with parts for both sides, be sure to replace both sides even if the noise is only coming from one side. The link on the end of the ropes have been reinforced to help prevent breaking and the pulleys are of a different bearing design. They are of a different material that will resist the attraction of dust build up and stay quiet. The fix for this is a new set of cables and pulleys. Sometimes the cables would break causing the door to fall. As dust and dirt get on the cables they would make noise usually a creaking or squeaking noise. The system used to open the door and hold it in place on these models uses rope cables and pulleys. If the door on your have a stainless steel tank dishwasher is making an annoying squeaking sound or simply drops open unless you support it there is a solution. These door are very Heavy and like I have said I have replaced them twice with a waiting time of three weeks for the repair man. I feel that paying $1000.00 dollars for a dishwasher would warrant using metal pieces instead of substandard plastic, for this application. It is easier to look at it and follow what is on the dishwasher than me clearly explaining it. Attach one end to the spring, line up in roller then attach to the dishwasher. You will need to order these pieces, they are all inclusive, and come for both sides of the door, at a whopping price of $15.00. Thess pieces are called the Dishwasher Door Balance Link. There is a number on the white plastic piece that looks like a L (it just slides out). You will see a (plastic) white roller, string(rope), and a piece that attaches to the dishwasher. Pull out the machine enough to see the out side- side. I had to remove a gray plastic circle piece on the inside to see the screw (it pops right out, don't loose it!). This could be behind the rubber on the sides. You will have to remove the screws that are holding your dishwasher under the counter. It is quite simple to fix, there is a special part that has all the pieces attached to it, except for the spring. I have had this issue TWICE now on a three year old dishwasher, and Sears charges you $150.+ to fix it.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |